lentilmimosa1

How to Replace a Kia Sportage Replacement Key The key in many Kia models has a keyless entry system built in. This key typically resembles an remote control, and is able to be replaced by a new one purchased from an Kia dealer or locksmith. Key fobs are prone to malfunction for several reasons, including a dead coin battery worn buttons water damage, signal interference and a faulty receiver module. Here are some suggestions to assist you in getting your Kia key fob that is a replacement for the sportage again. How to replace a remote key or a smartkey? It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start keys, or a regular non-transponder metal key The battery inside these keys will eventually need replacing. This is particularly the case if your car displays a message telling you that the remote or smart keys have low battery power. Luckily, this is a relatively simple process. To replace the battery on the key fob, remove the mechanical key from the slit in the back of the key fob and lift the cover. A small screw is found inside the key fob that holds the battery in its place. With a small screwdriver, remove the screw and pull out the old battery. Then, insert the new one and close the hole in the key fob. Test the key fob by pressing the lock and unlock buttons. It's good in case the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel chilly or when you need to go on errands around Brandon. Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your keys need to be reprogrammed, then you will need to be aware of the number printed on the key code tag and then record it in a safe place. How do I replace the battery? If the Kia key fob is unable to respond when you press the lock/unlock button, it's likely that the battery is not fully charged. A low battery could cause other issues, such as the check engine light flashing on or a delay in cranking the engine. It is quite simple to replace the key fob batteries by using only two tools. Make sure that you shut off your vehicle and close all doors prior to beginning. Find the small, metal or plastic piece at the bottom of your key fob, and play with it until a metallic key slides out. Then, you can insert the key in the handle of the door for the driver to unlock your car. To replace the key fob battery, take off the cover on the rear and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and orient the new one so that the “+” positive side is facing you and the “–” negative side is facing towards the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts. After the new battery has been installed and the key fob is turned on, turn it off and back on in the ignition several times until the door locks cycle. You can then test your Kia key fob to see whether it's functioning properly again. How to replace the smart key You may have either a standard keyfob or a Smart Key based upon the model of Kia Sportage. The difference between these is that the smart key comes with a small mechanical key blade that is hidden inside, while the standard fob doesn't. Both key fobs are equipped with an internal battery that will eventually require replacing. This is a straightforward process that takes just two minutes. Make sure you turn off your Kia and be on a flat, well-lit surface before you begin. Be aware that there are tiny pieces inside the fob which could be removed if not cautious. The release button for the small size is located on the lower backside. It's either a circular button or rectangular slot. When you press it, the mechanical key blade will pop out and you will be able to open the key fob. Once you have the key fob open, you can simply take off the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. When you're done, the key fob should allow you to lock and unlock your vehicle even if it's not running. How do I replace the mechanical key? The Kia keyfob is a great convenience which allows us to lock or unlock our car by simply pressing a button. But, as with all devices it will encounter issues occasionally. There are ways to solve these issues and ensure that our key fobs are in good working condition for the long run. kia key fobs The Key Lab of the most common problems is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this happens then try replacing the battery with a fresh new one. If this isn't enough to solve the issue, try using a standard flathead screwdriver to wedge the plastic casing of the fob open. Be careful not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a new one. Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure that it's working properly. If the fob still isn't working, contact an expert locksmith or dealer to resolve the issue. To avoid a lockout in the future make sure you get an emergency key that can work in all of the door and trunk cylinders.